baby diy: silicone & wooden bead teether


He’s like… Come on now, momma. Ok and I SWEAR I did not coordinate his cute narwhal pajamas with this project, this was just a crazy random happenstance.

I’d seen these beaded teethers & rattles show up in my instagram explore tab and thought they were so cute, so I tried my hand at making some for Nicky and quickly became obsessed. This diy is for a teether-slash-rattle that uses a variety of beads I’ll list below, but there are so many colours & styles & sizes of beads available it’s easy to customize them to your aesthetic. tbh this project is almost too easy to even require a diy but any excuse for pics of Nicky, right? Right.

I purchased all the supplies for this project (and all my other silicone bead projects) from Canadian DIY Supply <--click that link to get 10% off your order!
supplies:
2 x 1.75″ natural wood rings
2 x 17mm sapphire blue hexagon silicone beads
2 x 20mm navy blue round wooden crochet beads
4 x 15mm sapphire blue round silicone beads
4 x 14mm natural wood round beads
1 x 35″ midnight blue regular cord (I usually get some extra cord for if I mess up & need to restring on a new piece, which has happened more than once. The cord pictured is actually 60″ JUST IN CASE.)
not pictured:
embroidery scissors
tweezers (optional)
small bamboo skewer or round toothpick (optional)


Thread the beads onto the cord in the following pattern:
silicone round
wood round
silicone hexagon
wood round
silicone round
crochet round
Repeat this pattern until all your beads have been strung.

I’ve found that the crochet covering can sometimes become misaligned with the holes of the wooden bead; if this happens simply thread the skewer or toothpick through the bead and follow it with the cord. If necessary, use the tweezers to pull the cord through the far side of the crochet bead.

Once you have all the beads on the cord, thread the beaded cord through the wooden rings.

Tightly double-knot the ends of the cord together to form a loop, making sure there is a silicone bead on one side of the knot. Test that your knot is secure by pulling hard on the teether as if you are trying to break it. If your knot loosens or comes untied, re-knot and re-test until you are satisfied that it is secure. This is very important; please don’t skip testing!

Once you are confident that your knot is holding, slide the silicone bead over the knot. The hole of the silicone bead will stretch over the knot and then hold it tightly in place.

Using small, sharp embroidery scissors, trim the loose ends of the cord as close to the bead as possible. If necessary tuck the ends inside the bead with the knot. Test your teether’s knot by pulling again (DO NOT SKIP THIS TEST EITHER); if it comes untied you need to start over from the beginning with a new piece of cord, if it holds you’re done!

Here are all the different teethers & bracelets I’ve made…

clockwise from top left: forest green rounds & hexagons // round white marble in 3 sizes (a teether for Nicky AND a bracelet for me) // wooden rounds & rings with glacier grey rounds & isocahedrons and light grey crochet rounds // black, white & tangerine orange rounds (a bracelet for Gwen with a breakaway clasp) // the blue & wood teether from this diy (that I had to pry out of Nicky’s hand to photograph) // black & white rounds with glacier grey isocahedrons


It’s not a phone, guy.

DISCLAIMER: Loose beads are a choking hazard. Do not allow a child under the age of three to play with the loose beads. Never leave a child under the age of three unsupervised with these teethers. Always test your finished teethers to ensure the knots are safe and secure. Spot clean teethers as necessary. Do not soak in water or freeze any teethers with wood elements as it can cause the wood to crack, you can put teethers with only silicone beads in the freezer to chill them.

One Reply to “baby diy: silicone & wooden bead teether”

Leave a Reply

Your email address will not be published. Required fields are marked *